全文获取类型
收费全文 | 191篇 |
免费 | 71篇 |
国内免费 | 44篇 |
专业分类
航空 | 244篇 |
航天技术 | 9篇 |
综合类 | 11篇 |
航天 | 42篇 |
出版年
2022年 | 20篇 |
2021年 | 20篇 |
2020年 | 19篇 |
2019年 | 13篇 |
2018年 | 15篇 |
2017年 | 22篇 |
2016年 | 18篇 |
2015年 | 11篇 |
2014年 | 14篇 |
2013年 | 14篇 |
2012年 | 20篇 |
2011年 | 18篇 |
2010年 | 9篇 |
2009年 | 13篇 |
2008年 | 11篇 |
2007年 | 12篇 |
2006年 | 4篇 |
2005年 | 8篇 |
2004年 | 5篇 |
2003年 | 10篇 |
2002年 | 4篇 |
2001年 | 3篇 |
2000年 | 7篇 |
1999年 | 5篇 |
1998年 | 1篇 |
1997年 | 2篇 |
1995年 | 4篇 |
1993年 | 1篇 |
1992年 | 1篇 |
1989年 | 2篇 |
排序方式: 共有306条查询结果,搜索用时 100 毫秒
1.
《中国航空学报》2020,33(4):1192-1205
Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice. 相似文献
2.
沉井依靠自重消除刃脚阻力和外壁摩擦力下沉,本文对该项工艺的下沉、纠偏、挖土、封底主要技术问题进行介绍。 相似文献
3.
4.
导弹密封皮碗的可靠寿命试验与评估 总被引:3,自引:0,他引:3
对某型号导弹密封系统所用的橡胶材料进行了加速老化试验,通过分析给出贮存可靠及可靠寿命等性能指标随时间、温度的变化规律。并引进随温度变化的失效率与加速系数,来研究材料对贮存温度的敏感性,从而为确定最佳贮存温度提供依据。 相似文献
5.
迷宫密封—滑动轴承—转子系统的非线性动力稳定性 总被引:5,自引:0,他引:5
研究迷宫密封—滑动轴承—转子系统在不平衡量激励下的非线性动力稳定性。存在不平衡量的转子在旋转过程中受到周期激励,低转速时,转子作与激励同频率的周期运动,随着转速的提高,达到一定阈值时周期运动开始失稳。对迷宫密封的气动力采用Muszynska 非线性力学模型,支承采用短轴承,用打靶法求解转子运动周期解,并根据Floquet 理论分析了周期解的稳定性及失稳后的非线性动力学行为。 相似文献
6.
7.
用实验方法研究了直通式直齿和直通式斜齿在不同的齿类厚度与封严间隙比、齿数和流向的条件下,泄漏量随蓖齿前后压力比的变化规律。得到了几个有价值的结论,提出了计算其泄漏量的经验公式。计算结果与实验数据吻合良好。 相似文献
8.
9.
肖鑫%赵云峰%许文%詹茂盛 《宇航材料工艺》2007,37(1):6-10
简要概述了橡胶材料在承载及非承载状态下,加速老化试验方法及其测试手段的新进展;总结了橡胶材料寿命评估模型在计算机仿真、动力学及本构和唯象模型领域的新进展。 相似文献
10.
为了充分利用城市固体废弃物中的各项资源,本项工作将固体废弃物中的高密度聚乙烯(HDPE)回收后与废弃的木纤维、苯乙烯-丁二烯-苯乙烯(SBS)进行复合,成功地制备出SBS/再生型木塑复合材料,并进行了力学性能测试和水煮试验。结果表明,SBS的加入使木塑复合材料的冲击韧性得到显著改善,同时,复合材料的弯曲强度和弯曲模量没有明显的影响,表明SBS可以作为木塑复合材料的增韧剂。SBS/木塑复合材料经过8周、60℃的水煮后,复合材料的吸水率和厚度膨胀率均有所增加,弯曲模量和冲击韧性分别平均下降14.4%、10.8%。水煮试验初期复合材料的弯曲强度逐渐降低,然后又逐渐增大,第8周后弯曲强度增加的幅度约10%。木塑复合材料的冲击破坏模式以界面脱粘为主,而加入SBS后,复合材料的破坏以纤维断裂和基体断裂为主。 相似文献